Product Description Where you need the cable between the lights to be longer this extension cable will make extending the cable easy. The cable has connectors pre-fitted at both ends making it plug and play.
Product Description Where you need the cable between the lights to be longer this extension cable will make extending the cable easy. The cable has connectors pre-fitted at both ends making it plug and play. PLEASE NOTE: This product is only supplied to customers purchasing the LED products in the list below.
Product Description Additional End Caps to terminate the last connector in the chain to prevent short circuit or water ingress. Only required for installations outdoors or where the last connector is likely to come into contact with moisture or water. PLEASE NOTE: This product is only supplied to customers purchasing the LED products in the list below.
This attractive Spotlight/Downlight is IP67 Rated allowing it to be used in any wet environment such as Bathrooms, Showers, Saunas, Gardens and even Driveways. Draws just 3 Watts whilst producing light equivalent to a 30 Watt Halogen The rugged design makes them ideally suited for use in domestic and commercial settings, we have sold a large number of these RGB Lights for use in restaurant chains around the country. They are very reliable. The light fitting is finished with a flush fitting brushed 304 Stainless steel bezel. Due to the built-in dual voltage constant current driver the lamps will operate at the same brightness over all colours from 8v-24vdc. This means they can be used long distances away from the power supply (Transformer) and colour controller. The voltage drop over long distances will not affect the colour or the light output. Distances of 50 Metres or more are possible by using the Spotlights on our 24v Power Supplies. Where required it will fit into a GU10 / MR16 Lamp Holder. The Multi Chip LED has Red, Green, and Blue Emitters enabling the product to display 16.7 Million Colours when used with a Lightbox or Wi-Fi Lightbox, or 2.1 Million Colours if used with a Flexidriver. Up to 20 RGB Spotlights can be controlled from a single Lightbox or Flexi Driver.
Product Description The "T" cable is designed for use in installations where the wiring must be in place before the lights are installed such as bathrooms. The "T" cable is installed with 1M Extension cables (recommended), the 1M Extension cables should be looped behind where the wall and tiles will be and measurements taken. So when the holes are drilled the wire can be pulled through the Plinth Lights connected and the excess cable pushed back through into the cavity. Each cable can connect a maximum of 6 lights, for more lights in the run you will need to add additional "T" cables. The space between each "T" is 500mm with a total length of 3.1M. PLEASE NOTE: This product is only supplied to customers purchasing the LED products in the list below.
Mini Plinth Lights are 304 Stainless Steel and completely waterproof (IP67) allowing them to be used in a multitude of applications, such as; Plinth Lighting in the Kitchen, the Bathroom Floor, Walls, Ceiling, or even around the shower tray. They can also be used outside the house in Steps or Decking, the Stainless Steel ensures they will not rust.
- High Quality
Used on it's own it can display 7 Colours; White, Blue, Green, Red, Purple, Pink, Yellow, and Cyan by connecting the wire for the corresponding colour you require.
These lights don't t get hot so can be mounted in wood and plastics.
*If you connect them to one of our controllers (see below) it is possible to be operated via wired remote (ZAP), wireless remote (ZEN), or by Smartphone or Tablet. These allow the power to be switched off, with auto resume of last setting when switched on again at the light switch.
The auto resume makes it possible to use a PIR (Motion) Detector in the ceiling so the lights switch on when somebody enters the room and off again on a preset time when the room is unoccupied.
The latest version in our Plinth Light range this Plinth Light has a polished 304 Stainless Steel bezel with a non-glare frosted glass lens. It is waterproof to IP67 (temporary submersion under water) making it suitable for use indoors or outdoors in decks, steps, plinths, showers, floors, walls, and ceilings. - High Quality - Branded
Used on their own they can display 7 Colours; White, Blue, Green, Red, Purple, Pink, Yellow, and Cyan by connecting the wire for the corresponding colour you require.
These lights do not get hot so can be mounted on wood and plastic surfaces.
If you connect it to our Flexi (2.1 Million) Colour Driver the colour range will be virtually unlimited with gradual smooth colour sweeps which can be frozen on any colour.
We have additional controllers (see below) that allow them to be operated from an Infra-Red Remote, or our Lightbox (Smartphone / Tablet Controller)
The pictures on the right show the Plinth Lights being used with our Lightbox (£49), it allows you to select the colour onscreen by using the free App.
Our Litewave ® Stainless Steel LED Plinth & Floor Lights will provide attractive accent lighting in Floors & Skirting, Decking, Kitchen Plinths, and even Bath and Shower surrounds. Suitable for use Indoors or Outdoors • Low power • Does not get hot or project any heat or UV light • High Quality • Branded • 3 Year Warranty This product is finished with a 304 Stainless Steel bezel (will not rust) and is waterproof to IP67 (submersible). The light is emitted through an frosted polycarbonate lens which gives a soft light rather than a blinding beam. Unlike many cheap LED Plinth Lights available elsewhere these have built-in Constant Current Circuitry. This keeps the voltage and current to the LED at an optimum to reduce stress to the LED thus greatly extending it's lifetime.
Designed for customers requiring a discrete low powered light for use in ceilings, kitchen plinths, shower plinths and bath plinths & alcoves, steps and stairs, even outdoors in patios, decking and walls. Warm White This high quality fitting has a single SMD LED Chip housed within a 314 Stainless Steel body with a beautifully machined bezel, giving the product an attractive appearance whether switched on or off.
Due to the popularity of the 12vdc Mini Plinth Light we have developed a 24vdc version for use where long cable runs (20M or more) are required such as Edge-Lit Driveways, Garden path lighting, and use in conference centres and hotels. Ideal for low level lighting or marker lights. For use in ceilings, around skirting boards, kitchen plinths, shower plinths and bath plinths & alcoves, steps and stairs, even outdoors in patios, decking and walls. This high quality fitting has a single SMD LED Chip housed within a 314 Stainless Steel body with a beautifully machined bezel giving the product an attractive appearance whether switched on or off.